Dodge OBD1 Codes: Complete List Added with Meaning!

You are here because you searched for Dodge OBD1 codes, aren’t you? Most probably, you may not get the list of all OBD codes for your Dodge vehicles on the internet. That’s why we are here with this article.

You will find the full list of OBD1 codes in this article, as well as additional information. Also, we will show you the most accurate method on how to read the Dodge codes for older model vehicles. And also how to do it without a scanner.

Now, you seem to be excited? Hence, read this article from top to bottom.

Dodge OBD1 Codes: Applicable To All Models

OBD is one of the common words you may hear in the automobile industry. The word OBD is standard for on-board diagnostics. The modern vehicle has its own diagnostics that test and report the problem to you via the codes. These codes are known as OBD codes.

OBD1 and OBD2 are the two different types of OBD codes. OBD1 has proprietary plugs. They could not standardize emissions testing. And on the other hand, OBD2 has the standard ice plug, and it’s kind of a trapezoid.

After the diagnosis, you will see OBD1 or OBD2 codes based on your vehicle’s problems. There are various OBD codes for different brands. However, if you are a user of Dodge vehicles, then the OBD1 codes are very important for you.

Our finding shows that most of the users don’t have a list of all the codes of Dodge OBD1. That’s why we made the following tables. There you will get all the codes with proper descriptions.

Depending on what model Dodge vehicle you have, OBD1 codes can have slightly different meanings, but most of them are the same. This list does not guarantee that all the codes are accurate. Refer to your repair manual for the OBD1 codes specific to your vehicle.

Complete List of OBD1 Codes for Dodge

Dodge OBD1 Codes	Codes Description
65	Faulty power steering switch
64	Efficiency failures of catalytic converters
63	Write to the EEPROM was denied due to a PCM failure
62	Failure of PCM to store SRI mile
55	The end of the error messages (If this is the only message you receive, no errors have been found)
54	PCM is not getting a signal from the Cam
53	The internal control system failed
52	Rich in fuel systems
51	Lean fuel system
46	Low voltage on the charging system
44	The voltage of the battery temp sensor is out of range
43	Misfires in multiple or single cylinders
42	A voltage sensed is made on the fuel pump or the auto shutdown relay (ASD) at the controller
41	The generator field does not switch properly
37	Failure of the CKT or the park/neutral switch on the torque converter clutch solenoid
35	Control relay circuit for a rad fan
34	Solenoid circuits for speed control
33	Relay circuit for A/C clutch
32	Failure of the EGR system
31	Failure of the purge flow monitor or failure of the purge solenoid
27	Circuitry for controlling injectors
25	Short or open circuit detected in the motor driver circuit that controls the idle speed
24	Sensor reading out of range for the throttle position
23	Sensor for intake air temperature is out of range
22	The engine coolant temperature sensor is out of range
21	Oxygen sensor signal detected, but neither rich nor lean
17	Engine temperature too low, possible thermostat failure
15	Vehicle speed sensor not working
14	The voltage of the MAP sensor is too low
13	MAP remains unchanged from start to finish
12	Within the last 50 key-on cycles, the direct battery input to the PCM was disconnected
11	No reference signal during cranking, either a cam signal or an ignition signal

How To Get Dodge Codes Without A Scan Tool?

Here are the steps to reading the codes on Dodge Dakota without any scanner.

Step-1: Rotate Your Ignition Key

Put the ignition key in rotating to the on position without starting the vehicle. Take your key stick in the ignition and turn it on to off a couple of times, then the third one you leave it on. Doing that will make the engine light flash, and it will give you a series of flashes.

Step-2: Write Down The Dodge Codes:

Now you can see the flash on the engine light. Just write down what those codes are showing to you. There can be multiple Dodge codes. To avoid further hassles, we recommend you write all the codes on a page.

Step-3: Take Proper Steps To Fix The Issues:

After that, take the necessary steps to fix those code-related issues. If you need to do again, you will have to do the on and off-key cycle three times. However, if you have already written those codes, then it does not need to be repeated.

This is all you do to check the Dodge codes without using a scanner. Anyway, this method works on 1992 Dodge Dakota, early 200s Dodge Neons, Dodge Caravans, and other Dodge vehicles as well.

Frequently Asked Questions (FAQs)

How Do You Read The Codes On A 1992 Dodge Dakota?

Unlike modern Dodge Dakotas, older models did not have computer displays. However, there is actually a way to read the codes for these older models.

Thus here are the simple steps that you can follow to read the codes on a 1992 Dodge Dakota:

Step-1: Turn The Ignition Key On

Put the ignition key in, and turn it on, which is where all the lights, the radio, and everything come on, but the engine does not start to crank. Do that three times within five seconds or something like that. Basically, just do it as fast as you can.

Step-2: Count The Flashes

After that, check the engine light. It will stay on for a little bit, and then it will flash. You need to count the flashes. The first set of flashes will be number 12. There will only be one flash and then a noticeable pause. Two flashes, and then another noticeable pause.

Step-3: Read The Codes

Now the codes will appear to you. You can see the codes, and you can read them too. However, to run the end of the stream of codes, you get two five five which is the end of sequences. So, it will flash five times, and then it won’t come back on.

Anyway, by following this method, you will be able to read the codes on almost all the Dodge trucks prior to 1996. Because after that, they make the things digitized.

Last Few Words

After reading our article, we are confident that you will gain all the knowledge you need about Dodge OBD1 codes. Here we also share the methods of reading Dodge codes with or without a scanner. You can apply all our described methods to almost every model of Dodge vehicle.

However, before doing anything, check the owner’s manual. A specialist mechanic should be consulted before attempting a DIY repair. By doing so, you can prevent such damages that you might cause due to a lack of knowledge.

Would you find our article helpful? Let us know in the comment box. And please write to us if you still have any queries regarding the automobile field. Our team will be more than happy to assist you.

You Can Also Read:

• Are Diehard Batteries Good Or Not?
• It’s High Time You Find Out the F150 Misfire Symptoms
• What’s The Most Common F150 Panoramic Roof Problems
• Dare To Solve the Ford F150 Shift Linkage Problems Yourself?